prikaz prve stranice dokumenta Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?
  Preuzmi
PDF 1.92 MB
Znanstveni rad - Izvorni znanstveni rad
Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?
Materials, 14 (2021), 3; 515. https://doi.org/10.3390/ma14030515
Marović, Danijela; Par, Matej; Crnadak, Ana; Šekelja, Andjelina; Negovetić Mandić, Višnja; Gamulin, Ozren; Rakić, Mario; Tarle, Zrinka

Citirajte ovaj rad

Marović, D., Par, M., Crnadak, A., Šekelja, A., Negovetić Mandić, V., Gamulin, O. ... Tarle, Z. (2021). Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?. Materials, 14. (3). doi: 10.3390/ma14030515

Marović, Danijela, et al. "Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?." Materials, vol. 14, br. 3, 2021. https://doi.org/10.3390/ma14030515

Marović, Danijela, Matej Par, Ana Crnadak, Andjelina Šekelja, Višnja Negovetić Mandić, Ozren Gamulin, Mario Rakić i Zrinka Tarle. "Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?." Materials 14, br. 3 (2021). https://doi.org/10.3390/ma14030515

Marović, D., et al. (2021) 'Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?', Materials, 14(3). doi: 10.3390/ma14030515

Marović D, Par M, Crnadak A, Šekelja A, Negovetić Mandić V, Gamulin O, i sur.. Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?. Materials [Internet]. 21.01.2021. [pristupljeno 14.11.2024.];14(3). doi: 10.3390/ma14030515

D. Marović, et al., "Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?", Materials, vol. 14, br. 3, Siječanj 2021. [Online]. Dostupno na: https://urn.nsk.hr/urn:nbn:hr:127:600459. [Citirano: 14.11.2024.]

Za citiranje koristite ovu mrežnu adresu: https://urn.nsk.hr/urn:nbn:hr:127:600459
Prijavite se u repozitorij kako biste mogli spremiti objekt u svoju listu.
Podaci o radu
Naslov (engleski)Rapid 3 s Curing: What Happens in Deep Layers of New Bulk-Fill Composites?
AutorDanijela Marović
AutorMatej Par
AutorAna Crnadak
AutorAndjelina Šekelja
AutorVišnja Negovetić Mandić
AutorOzren Gamulin
AutorMario Rakić
AutorZrinka Tarle
Autorova ustanovaInstitut za fiziku
Autorova ustanovaSveučilište u Zagrebu
Medicinski fakultet
Autorova ustanovaSveučilište u Zagrebu
Stomatološki fakultet
Znanstveno / umjetničko
područje, polje i grana		BIOMEDICINA I ZDRAVSTVO
Dentalna medicina
Sažetak (engleski)
This study assessed the influence of rapid 3 s light curing on the new generation of bulk-fill resin composites under the simulated aging challenge and depths up to 4 mm. Four bulk-fill materials were tested: two materials designed for rapid curing (Tetric PowerFill—PFILL; Tetric PowerFlow—PFLW) and two regular materials (Filtek One Bulk Fill Restorative—FIL; SDR Plus Bulk Fill Flowable—SDR). Three-point bending (n = 10) was used to measure flexural strength (FS) and flexural modulus (FM). In the 3 s group, two 2 mm thick specimens were stacked to obtain 4 mm thickness, while 2 mm-thick specimens were used for ISO group. Specimens were aged for 1, 30, or 30 + 3 days in ethanol. The degree of conversion (DC) up to 4 mm was measured by Raman spectroscopy. There was no difference between curing protocols in FS after 1 day for all materials except PFLW. FM was higher for all materials for ISO curing protocol. Mechanical properties deteriorated by increasing depth (2–4 mm) and aging. ISO curing induced higher DC for PFLW and FIL, while 3 s curing was sufficient for PFILL and SDR. The 3 s curing negatively affected FM of all tested materials, whereas its influence on FS and DC was highly material-specific.
Ključne riječi (engleski)
Jezikengleski
Vrsta publikacijeZnanstveni rad - Izvorni znanstveni rad
Status objaveObjavljen
Vrsta recenzijeRecenziran - međunarodna recenzija
Verzija publikacijeObjavljena verzija rada (izdavačev PDF)
Naslov časopisaMaterials
Brojčani podacivol. 14, br. 3, 515
e-ISSN1996-1944
DOIhttps://doi.org/10.3390/ma14030515
URN:NBNurn:nbn:hr:127:600459
Datum objave publikacije2021-01-21
URL dokumentahttps://www.mdpi.com/1996-1944/14/3/515
Vrsta resursaTekst
Prava pristupaOtvoreni pristup
Uvjeti korištenjaIkona licence Imenovanje 4.0 međunarodna (CC BY 4.0)
Datum i vrijeme pohrane2022-11-10 12:17:57